I have a 1980 Monte Carlo and need to know whats the part number for the bulb that comes on that is down near the emergency brake pedal, is it a 1157 bulb or what?Thanks
Have anyone ran these Felpro 1144-053 head gaskets on a SBC 400 engine with NO problems, I see that they only have the steamholes in the gaskets closer to the intake side of the heads?Thanks
I have a 1988 Monte Carlo SS with a original 305 sbc engine and would like to know what years aftermarket intake would fit this engine it has centerbolt valve covers on it?Thanks
How do I remove the smog pump belt on my 1988 Monte Carlo SS 305 engine, I see the bracket up yop ,do I have to remove the cricket looking brace also?Thanks
Can anyone tell me where I can get the round seal and part number that goes on the 200r4 filter that goes into the transmission ,I'm missing mines and don't want to remove the old one yet and find out that it is damaged rather have one thats ready to go?Thanks
I have a 1988 Monte Carlo SS 305 engine and im looking for a locking vented gas cap,anyone know the part number for a Stant or Gates gas cap or any other gas caps with locking and vented?Thanks
How do I remove the oil pressure sending unit the one that is behind the distributor coming of a tee on a 1988 Monte Carlo SS 305 engine cant seem to get the special socket on it because of the angle any other suggestions?Thanks
I need a fan clutch for my 1988 Monte Carlo SS 305 engine and was wondering what is a good brand and part number for a fan clutch, I was thinking about the Hayden 2747 and are there any fan cluches that are made in the USA?Thanks
I have a 1988 Monte Carlo SS with 107K original miles that runs and drives great ,but the temp gauge goes up and down from like 190 to 260 and the oil gauge goes to zero when at a stop but shoots up to 40 psi as soon as the gas is pressed and I'm driving, could this be BAD gauges or what?Thanks
I have a pair of AFR SBC ENFORCER HEADS that are new but are 2 different part numbers, one being part number 1001 straight plugs and the other being part number 1006 angle plugs ,will these heads work together on a sbc engine by one being straight plugs and the other being angle plugs?Thanks
Im running a Holley ultra street avenger 670 carburetor on my sbc 406 daily driver and was wondering would it be better to install a Holley ultra 650 double pumper with electri choke on my daily driver I know I might be getting less fuel mileage from the double pumper but what about daily...
I have a autometer water temperature gauge installed in my sbc engine engine doesn't overheat but if parked in the hot weather for a long time when i get in the car the temperature hand will be reading like 140 degrees ,any help.Thanks
I will be installing a Holley ultra street avenger on my engine, where is a good place to install the ground wire frome the choke,can i install it to one of the carburetor studs scews or to my aluminum intake manifold?Thanks
I have a 700r4 transmission and i over tighten the speedometer cable and the gear housing snapped can I just unbolt the clamp and pull the gear housing out and replace it so my speedometer will work again?Thanks
I have a recently built sbc 406 I installed timing chain as usual crank dot up cam dot down. I ran engine on engine stand fired right up and run put engine back at tdc removed distributor and installed another distributor, tdc xero on balancer and rotor point to number 1 cylider,finally got...
I just installed a engine in my 80 monte carlo and sometimes it will not get 12 volts to the distributor, i can run hot wire the distributor and it will fire up after that it will fire up using original distributor wire wasted doing this before installing new engine any HELP?THANKS
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.